Article

 

 

This great article down below on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is amazingly attention-grabbing. Check it out for your own benefit and decide what you think about it.

Installing a bathtub isn't exactly rocket science, yet it does call for strong plumbing, woodworking, and also occasionally, tiling skills. Changing an old bath tub with a brand-new one is additionally a reasonably hard task. If the old bathtub is easily easily accessible, the job can relocate rapidly; if you need to open a wall to remove the old tub and also position the new bath tub, the job is much harder. In either case, the task is within a house handyman's skills, although you will certainly require a helper to move out the old tub and embeded in the brand-new one. Make certain you have qualified on your own for the task as well as are comfortable attempting it. As opposed to working with a professional to take over a halfway-completed task, it is much better to consider utilizing one before you start. Possibilities are you may require a professional plumber to make tube links.
This post will aid you install a brand-new tub in your bathroom if you have actually already gotten a new bathtub and do not need to transform the arrangement of your previous water system pipes.
Your devices and product checklist need to comprise the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipe Caps


 

Preparing for the Installment

Firstly, the sustaining framework supplied with the bathroom should be fitted (if called for) according to the producer's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to see to it that if the tap features a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets device to prevent stress on the bath tub.
Fit the versatile faucet connectors to the bottom of the two faucets making use of 2 nuts and olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you utilize every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final setting.

 

 

Removing Old Taps

If you need to replace old taps with new ones as a part of your installation, then the first thing you ought to do is disconnect the supply of water. After doing so, turn on the taps to drain any water remaining in the system. The process of getting rid of the existing faucets can be fairly bothersome as a result of the limited gain access to that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the remaining water that will originate from the pipelines. When the supply pipes have been removed, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any old securing substance.
Before proceeding to fit the new taps, compare the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.

 

 

Installing the Bathtub

Making use of both wooden boards under its feet, place the bathtub in the called for position. The wooden boards are helpful in equally spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 little points.
The next objective is to make sure that the tub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bath tub till the level reads degree.
To mount taps, fit the bottom of the furthest adaptable faucet connector to the appropriate supply pipeline by making a compression join; then do the very same for the other tap.
Activate the water system and examine all joints as well as new pipework for leakages as well as tighten them if necessary. Fill up the bathtub as well as also examine the overflow electrical outlet and the regular outlet for leakages.
Lastly, take care of the bath paneling as defined in the producer's user's manual. Tiling as well as sealing around the bath tub needs to wait until the tub has actually been utilized at the very least once as this will certainly settle it right into its last setting.

 

 

Suitable New Taps

If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and also the other end offers a link to the existent supply pipes.
If you require to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin guaranteeing that the washing machines remain in place in between the tap as well as the sink. Safeguard the tap in position with the manufacturer supplied backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal tap ports. The previous kind should be linked to the faucet finishes initially, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.

 

 

Tiling Around the Tub

In the location where the bathroom fulfills the tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to fracture a rigid seal, causing the water to permeate the wall between the bathroom as well as the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to constantly load the bath tub with water prior to sealing, to allow for the activity experienced when the bathtub is in usage. The sealer can break fairly very early if you do not take into consideration this movement prior to securing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or water resistant adhesive and cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

We were introduced to that write-up about How to Install a Bathtub Yourself from a good friend on a different web page. Liked our blog? Please share it. Let other people discover it. Thank you so much for taking the time to read it.

Estimate

Source This Article

 

 

The article author is making a few great pointers related to Why Your Water Pipes Are Noisy and How To Shut Them Up overall in the article just below.

To detect noisy plumbing, it is very important to determine very first whether the undesirable audios occur on the system's inlet side-in various other words, when water is transformed on-or on the drain side. Sounds on the inlet side have actually varied reasons: too much water pressure, worn shutoff and faucet components, improperly connected pumps or various other devices, incorrectly put pipeline bolts, and plumbing runs including way too many tight bends or other limitations. Sounds on the drain side typically come from bad area or, as with some inlet side noise, a design having limited bends.

 

Hissing

Hissing noise that occurs when a tap is opened a little usually signals excessive water pressure. Consult your regional water company if you presume this trouble; it will certainly be able to tell you the water pressure in your area as well as can mount a pressurereducing shutoff on the inbound water supply pipe if required.

 

Thudding

Thudding sound, commonly accompanied by trembling pipelines, when a tap or device valve is turned off is a problem called water hammer. The noise and vibration are caused by the reverberating wave of pressure in the water, which all of a sudden has no location to go. Often opening up a shutoff that releases water swiftly right into an area of piping having a constraint, joint, or tee installation can generate the very same problem.
Water hammer can generally be treated by setting up installations called air chambers or shock absorbers in the plumbing to which the issue valves or faucets are linked. These devices allow the shock wave created by the halted flow of water to dissipate in the air they contain, which (unlike water) is compressible.
Older plumbing systems might have brief upright areas of capped pipe behind walls on faucet runs for the same objective; these can at some point loaded with water, lowering or destroying their effectiveness. The cure is to drain the water system completely by shutting off the main water supply valve and opening all faucets. After that open up the primary supply shutoff as well as close the faucets one at a time, starting with the faucet nearest the valve and finishing with the one farthest away.

 

Babbling or Shrilling

Extreme chattering or shrieking that happens when a valve or faucet is turned on, and that usually goes away when the installation is opened totally, signals loosened or defective inner components. The service is to replace the shutoff or tap with a new one.
Pumps and also home appliances such as washing machines and also dishwashing machines can move electric motor noise to pipelines if they are incorrectly connected. Connect such products to plumbing with plastic or rubber hoses-never rigid pipe-to isolate them.

 

Various Other Inlet Side Noises

Squeaking, squealing, scratching, breaking, as well as tapping generally are triggered by the expansion or tightening of pipes, usually copper ones supplying hot water. The noises occur as the pipelines slide against loose fasteners or strike neighboring home framing. You can often determine the place of the problem if the pipelines are subjected; just adhere to the audio when the pipelines are making noise. More than likely you will certainly discover a loosened pipeline hanger or a location where pipes exist so near to floor joists or various other framing pieces that they clatter versus them. Attaching foam pipeline insulation around the pipes at the point of contact must fix the trouble. Make sure straps and also hangers are safe and supply ample support. Where feasible, pipe bolts need to be connected to substantial structural aspects such as foundation walls as opposed to to framing; doing so reduces the transmission of resonances from plumbing to surfaces that can magnify and also transfer them. If connecting bolts to framing is inevitable, cover pipes with insulation or other resistant material where they get in touch with bolts, and sandwich the ends of brand-new bolts between rubber washers when mounting them.
Remedying plumbing runs that deal with flow-restricting tight or countless bends is a last option that must be taken on only after getting in touch with an experienced plumbing specialist. However, this situation is relatively usual in older houses that might not have actually been built with indoor plumbing or that have actually seen several remodels, especially by novices.

 

Drain Noise

On the drain side of plumbing, the principal objectives are to eliminate surfaces that can be struck by dropping or hurrying water and to protect pipelines to have unavoidable noises.
In brand-new building and construction, bathtubs, shower stalls, bathrooms, and also wallmounted sinks and also basins ought to be set on or versus resistant underlayments to lower the transmission of sound through them. Water-saving bathrooms as well as taps are much less noisy than conventional models; install them instead of older types even if codes in your area still permit using older components.
Drains that do not run up and down to the cellar or that branch right into straight pipeline runs sustained at flooring joists or various other framing present especially problematic noise problems. Such pipes are large enough to radiate significant resonance; they likewise lug substantial quantities of water, that makes the scenario even worse. In brand-new building and construction, define cast-iron dirt pipelines (the large pipes that drain toilets) if you can afford them. Their massiveness contains much of the noise made by water passing through them. Also, avoid routing drainpipes in walls shared with rooms and also areas where individuals collect. Wall surfaces consisting of drains should be soundproofed as was described previously, making use of dual panels of sound-insulating fiber board as well as wallboard. Pipes themselves can be wrapped with special fiberglass insulation made for the purpose; such pipelines have a resistant plastic skin (often consisting of lead). Results are not always satisfactory.

 

WHY IS MY PLUMBING MAKING SO MUCH NOISE?

 

This noise indeed sounds like someone is banging a hammer against your pipes! It happens when a faucet is opened, allowed to run for a bit, then quickly shut — causing the rushing water to slam against the shut-off valve.

To remedy this, you’ll need to check and refill your air chamber. Air chambers are filled with — you guessed it — air and help absorb the shock of moving water (that comes to a sudden stop). Over time, these chambers can fill with water, making them less effective.

You’ll want to turn off your home’s water supply, then open ALL faucets (from the bathroom sink to outdoor hose bib) to drain your pipes. Then, turn the water back on and hopefully the noise stops! If you’re still hearing the sound, give us a call to examine further.

 

Whistles

 

Whistling sounds can be frustrating, as sometimes the source isn’t easily identified. However, if you can pinpoint which faucet or valve that may be the cause, you’ll likely encounter a worn gasket or washer — an easy fix if you replace the worn parts!Whistling sounds from elsewhere can mean a number of things — from high water pressure to mineral deposits. Your best plan of attack here is to give our plumbing experts a call. We’ll be able to determine where the noise is coming from and what the cause may be, then recommend an effective fix!

 

Cracks or Ticks

 

Cracking or ticking typically comes from hot water going through cold, copper pipes. This causes the copper to expand resulting in a cracking or ticking sound. Once the pipes stop expanding, the noise should stop as well.

Pro tip: you may want to lower the temperature of your water heater to see if that helps lessen the sound, or wrapping the pipe in insulation can also help muffle the noise.

 

Bangs

 

Bangs typically come from water pressure that’s too high. To test for high water pressure, get a pressure gauge and attach it to your faucet. Water pressure should be no higher than 80 psi (pounds per square inch) and also no lower than 40 psi. If you find a number greater than 80 psi, then you’ve found your problem!

Next step is to give us a call in order to install a pressure regulator. Trust us, you don’t want to wait to resolve this issue. Not only is the sound annoying, but high water pressure can be destructive to your home — including damaging certain appliances, like your washer and dishwasher.

 

Dripping

 

You might be accustom to the slow quiet drip your kitchen faucet makes. You might have even tuned out your bathroom sink dripping and drabbing all day long — but it’s time to find its cause.

A slow drip could signify a variety of easy to fix issues, such as a worn out O ring, or loose part. And by ignoring the drip, you could be wasting up to 2,000 gallons of water a year! So start conserving water — get it looked at ASAP.

https://www.pwessig.com/blog/2018/december/why-is-my-plumbing-making-so-much-noise-/

 

Do you enjoy more info about How To Fix Noisy Pipes? Write feedback down the page. We'd be interested to find out your views about this article. We are looking forward that you visit us again before long. Liked our review? Please share it. Let someone else check it out. Thank you so much for your time invested reading it.

Schedule Now!